Skip to content
Design Gallery, home

Journal Craft & Product

Planning a Kitchen Remodel: Eight Decisions to Make Before You Visit a Gallery

Layout, appliances, cabinet doors, surfaces, ventilation, lighting, the trades and timing: what to settle in order, and where to see them in Roseville.

Robert VolkanovNovember 20, 20265 min read

Towers of cabinet door samples in painted white, blue, green, gray and wood finishes at Design Gallery Roseville
Towers of cabinet door samples in white, pale blue, green and wood finishes, framed and flat, on the Roseville gallery floor.

A kitchen remodel comes down to eight decisions, made in this order: layout, appliance package, cabinet door style and stain, surface material, ventilation, lighting, electrical and plumbing, and timeline. Each one narrows the next, so a plan made in that order arrives at a gallery visit with the right questions and leaves knowing what fits the project and what comes next. Most sections name where to see that decision in Roseville.

1. Layout

Layout comes first because everything else has to fit inside it. Start with what the room has to do: who cooks, how many people cook at once, where people sit and where they walk through. Measure the room and mark the doors, windows and anything that cannot move. Then choose a shape: a single wall, a galley, an L, a U, or a plan with an island.

Clearances decide how much of that fits. The National Kitchen & Bath Association recommends a work aisle at least 42 inches wide for one cook and 48 inches for more than one, and a walkway of at least 36 inches, and it adds to each guideline that state or local codes may apply. Our guide to kitchen island size and clearances sets out the rest of its figures, and the kitchen displays near Sacramento page gathers finished kitchens to walk at full size.

2. The appliance package

Choose the appliances before the cabinetry, because the cabinets are built around them. List how you cook: a range, or a cooktop with wall ovens; gas or induction; a steam oven; a warming drawer; a second dishwasher; wine or beverage storage. Each choice sets a width in the plan, and many set a requirement behind the wall.

Then decide how the appliances should look. Panel-ready refrigeration and dishwashers take a cabinet front, which our piece on what panel-ready means explains. If a steam oven is on the list, our piece on whether a steam oven is worth it covers what it changes in daily cooking. For refrigeration columns, our comparison of Sub-Zero and Thermador columns lists the questions to ask about widths, hinges and panels.

At Design Gallery, Kyoto presents an expansive JennAir collection, with several cooking technologies, wall ovens, refrigeration, beverage storage, dishwashing and ventilation, unified beneath Vadara Gossamer Sands quartz. Kyoto is a finished display; the appliances that run are in the working kitchen, where the range is brought to heat during a session.

3. Cabinet door style and stain

The cabinet door and its finish set the tone of the room. Decide the door profile first: a flat slab, a framed shaker-style door or a more detailed panel. Then the finish: paint, a stain on a chosen wood, or a clear finish that keeps the wood’s own color. Judge a stain on the wood it will be made in, at full height.

Bologna shows how much finish alone changes, with one Essenza Oslo door profile presented in both Walnut and White. In Coffee Connect, DreamLine cabinetry in the Eureka door style in Swiss Coffee meets island fronts in Driftwood-stained rift white oak, and Napa sets DreamLine Giovanna cabinetry in California Oak-stained rift white oak. The DreamLine custom cabinetry near Sacramento page covers the custom line, designed and built in Northern California.

4. Surface material

Countertops are chosen against the cabinetry, not on their own. The main families are natural stone, such as quartzite and marble; engineered quartz; and sintered surfaces such as Dekton. Our pieces on quartz and quartzite in the kitchen and on Dekton and engineered quartz set out what each maker says about pattern, care, sealing and heat.

Choose from a full slab where you can, because veining across a large piece reads differently from a sample. The slab and stone gallery near Sacramento page gathers the countertop displays. Cambria Suit pairs clear-finished rift white oak with Cambria Remington Brass at full scale, to show how grain and veining interact, and the Table Station is set up for comparing materials and discussing them.

5. Ventilation

Ventilation is chosen with the cooktop, not after it. Decide whether the hood should stand out or disappear: a statement hood over the range, an insert hidden in the cabinetry above, or a downdraft that rises from the counter. Ask your designer to read the cooktop and ventilation specifications together before the cabinetry is drawn.

Oslo treats Zephyr ventilation as part of the kitchen’s architecture, with sculptural wall hoods, a Satin Gold statement hood and telescopic downdrafts. In Siena, a BlueStar Abbaka Normandy hood anchors cabinetry in Carbon-stained alder.

6. Lighting

Plan lighting in layers: general light for the room, task light on the counters and the cooktop, and decorative fixtures over an island or a table. Decide fixture size and finish with the rest of the palette, not at the end. Lucerne presents decorative lighting at full scale alongside the gallery’s kitchens and baths, so a fixture can be judged against the materials it will hang over.

7. Electrical and plumbing

Moving a sink, adding a gas line or switching to induction is work for a licensed contractor, so this guide gives no technical advice. Before a visit, note what you want to move or add: the sink, the range, the dishwasher, a sink or cooktop in an island. Bring that list to the visit.

Design Gallery itself is not a contractor. What you choose at the gallery is recorded with model numbers, finish codes and rough-in requirements, ready for whoever runs the project.

8. Timeline and lead times

Set the order of work before you set a date. Selections come first, because the cabinetry is built around the appliances and the countertops are cut to the cabinetry. DreamLine builds its cabinetry to specification in its own Northern California shop, and countertops are cut by a fabricator working from the specification.

Lead times vary by maker and by model, so ask for the current lead time on each appliance and material you select, and let the longest one shape the schedule.

How a gallery visit with a designer works

The book a visit page describes three kinds of visit: a walkthrough of the environments, room by room; a private room with your designer, your plans on the table and every material within reach; and a working-kitchen session, where you see the equipment steam, sear and hold. You leave knowing what fits your project and what comes next.

Bring your plans and measurements if you have them, and your designer or builder if they are part of the project. Homeowners who come without a designer are hosted by the gallery team. A first walkthrough runs about half an hour, and a working session with drawings on the table runs longer. Any further contact from the gallery team is at your request.

Designers bringing a client can reserve a private room and bring the client themselves, through the trade program for designers. A client introduced by a design professional stays with that professional.

Questions

Questions, answered

What should I decide before a kitchen remodel?

Eight things, in this order: layout, appliance package, cabinet door style and stain, surface material, ventilation, lighting, electrical and plumbing, and timeline. Each decision narrows the next, so settling them in order saves revisiting earlier choices.

Should I choose appliances or cabinets first?

Appliances. The cabinetry is built around them, and each appliance sets a width in the plan. Panel-ready refrigeration and dishwashers also take a cabinet front, so the door style follows from that choice.

Who handles electrical and plumbing changes in a kitchen remodel?

A licensed contractor does that work. Design Gallery itself is not a contractor; it records what you choose with model numbers, finish codes and rough-in requirements for whoever runs the project.

Can I bring my designer to a gallery visit in Roseville?

Yes. At Design Gallery, private rooms seat a full project team with your drawings on screen, a few steps from the environments you are choosing between. Homeowners without a designer are hosted by the gallery team.

On the floor

Where to see DreamLine Custom Cabinetry

Custom cabinetry near Sacramento

Visit the Gallery

See it working on the Roseville floor.

Or call (916) 500-5417Monday –⁠ Saturday, 9:00 AM –⁠ 5:00 PM

Keep reading